在平等體積下，液壓升降機液壓設備能比電氣設備發生更大的動力。在平等功率下，液壓設備的體積和質量小，即其功率密度大，布局緊湊。
Under equal volume, hydraulic lift hydraulic equipment can be greater than the electrical power generating equipment. Under equal power, small volume and mass of hydraulic equipment, that is, its power density, compact layout.
升降機液壓傳動易于對液體壓力、流量或活動方向進行調理或操控。尤其是在自動化較高的場合，整個傳動設備能完成很雜亂的按次舉措，也能便利的完成長途操控和自動化。液壓設備任務比擬平穩。由于質量和慣性小、反響快，液壓設備易于完成疾速起動、制動和頻頻的換向。
Hydraulic lift is easy on the liquid pressure, flow conditioning or activity direction or control. Especially in the case of high automation, the entire transmission equipment can be completed very messy Pay initiatives, but also to facilitate the completion of the long-distance control and automation. Hydraulic equipment task compared to stable. Since the mass and inertia of small, fast response, easy to complete hydraulic equipment fast starting, braking and frequent commutation.
液壓升降機操控體系(不帶手壓泵的液壓集成塊)： 在運用時必須將回油閥旋鈕按順時針方向擰緊，把手動換向閥手柄拉到“中立”的方位，發動電機(或柴油機)使體系任務，然后把換向手柄拉到“起升”的方位，液壓升降機起升，抵達所需高度時，在將換向手柄推到“中立”的方位，液壓升降平臺中止上升還要封閉電機，即可作業。下落時，松開回油閥(逆時針方向旋轉)，液壓升降機依托自重就可下落。
Hydraulic lift control system (hydraulic manifold without hand pump): You must return valve knob clockwise twist in the use of tight, pull the manual valve handle "neutral" position, start the motor (or diesel engine ) so that the system task, and then reversing lever pulled "lifting" position, hydraulic lifts lifting, upon arrival at the desired height, in the reversing lever pushed to the "neutral" position, hydraulic lifting platform also suspend rise closed motor, can work. When falling, loosen the oil return valve (counter-clockwise), relying on the weight of the hydraulic lift can fall.
電磁換向閥液壓操控體系：首要按動電動機開關，油泵打油(注重，不要回轉)次時油泵處于卸荷狀況，按起動開關，電磁換向閥1DT任務，液壓升降平臺起升。抵達所需任務高度時，封閉起升開關，即可作業。按下落開關，電磁換向閥2DT任務，液壓升降機依托自重下落到原始方位。
請長按保存二維碼后點擊確定按鈕，進入微信掃一掃界面,點擊右上角‘相冊’選擇我們的二維碼,再點擊右上角‘完成’識別添加。
(為防止瀏覽器錯誤識別，請勿直接在瀏覽器中識別二維碼)
